Go to content

FM broadcast antennas 87.5–108 MHz for professional radio networks - Protel Antennas - Professional Antennas for Telecomunications

Protel Antennas 38 years - 2026
Logo Protel antennas
PROFESSIONAL ANTENNAS
FOR TELECOMMUNICATIONS
SELECT THE FREQUENCY BAND
Skip menu
SELECT THE FREQUENCY BAND
Skip menu

FM broadcast antennas 87.5–108 MHz for professional radio networks

Role of 87.5–108 MHz FM band in professional broadcasting

The 87.5–108 MHz band, also known as VHF Band II, is dedicated to FM broadcasting and remains one of the most widely used platforms for analogue radio services. Professional FM networks require antennas with high reliability, stable electrical performance and carefully controlled radiation patterns, both in azimuth and in elevation. Depending on the coverage goals and regulatory constraints, the antenna system can be configured to serve dense urban areas, wide regional zones or specific protected regions.

In modern FM installations, antennas are often operated in multi-bay configurations and fed by combiners that allow several transmitters or programmes to share the same radiating system. This makes the antenna a critical component of the overall broadcast chain: its behaviour must be predictable, repeatable and compatible with high continuous power levels and demanding modulation formats.

Typical FM antenna types in the 87.5–108 MHz range

In the 87.5–108 MHz band Protel designs and manufactures several families of FM broadcast antennas, based on different radiating elements and mechanical layouts:

  • FM dipole antennas used as single radiators or in multi-bay arrays around the tower. They provide omnidirectional or shaped azimuth patterns depending on the number and arrangement of elements, and are widely used in regional and local stations.
  • Directional FM yagi antennas mainly employed for specific coverage targets, feeder links and special applications where a defined main lobe and high front-to-back ratio are required. Yagi structures offer increased gain and pattern control.
  • Log-periodic FM antennas used when wideband operation or multi-service capability is needed within and around the FM band. Log-periodic designs ensure a controlled impedance and radiation pattern over a broad frequency range.

Each antenna family is available with different gain values, polarisation options and mechanical configurations, so that the system designer can match the antenna characteristics to the required coverage and to the constraints of the transmitter site.

Multi-bay systems, pattern control and combiners

FM broadcast antennas are rarely used as single radiators. In most professional installations, they are combined into multi-bay systems, stacking several elements vertically and, where needed, arranging them azimuthally around the mast. By adjusting the number of bays, inter-bay spacing and phasing, it is possible to tailor the vertical and horizontal patterns: increasing the gain in a given direction, limiting radiation towards protected areas or complying with coverage masks specified by regulators.

These antenna systems are typically fed by combiner networks that allow multiple transmitters to share the same array. In this context, parameters such as impedance, VSWR, power handling and isolation become critical. Protel FM antennas are designed to work reliably with combiners and filters, maintaining stable electrical characteristics over the entire 87.5–108 MHz band.

Installation scenarios and mechanical considerations

FM broadcast antennas must withstand long-term outdoor operation, often at considerable height and in severe climatic conditions. Mechanical robustness, wind load and corrosion resistance are therefore essential design aspects. Protel FM antennas are manufactured using high-quality materials such as aluminium and stainless steel, with mounting hardware engineered for secure installation on towers, masts and existing structures.

Depending on the project, antennas can be installed on dedicated masts or on shared sites that already host other services (for example VHF, UHF, microwave links). In these cases it is important to consider mutual coupling, mechanical clearances and the overall loading of the structure. Proper planning of antenna positions, heights and orientations allows the designer to achieve the desired coverage with minimum impact on existing systems.

Guidelines for selecting an FM broadcast antenna

Selecting the right FM broadcast antenna system requires a clear definition of coverage targets, transmitter power levels, site constraints and regulatory limits. Omnidirectional dipole arrays are typically used for uniform coverage around the site, while directional systems based on panels or yagi antennas can concentrate energy where needed and reduce radiation in unwanted directions.

The number of bays, the gain and the vertical beam shape must be chosen in combination with the transmitter power and feeder configuration. In multi-programme sites, compatibility with RF combiners and filters is a key requirement. Protel FM antennas for 87.5–108 MHz are designed to support these scenarios, providing a reliable platform for local, regional and national FM networks.

For the list of available models and detailed electrical and mechanical specifications, please refer to the FM antennas 87.5–108 MHz product catalogue page .


CONTACT
COMPANY
NEW
OTHER APPLICATIONS
PROTEL Antennas Via Magellano 3 A/B 6
20090 CESANO BOSCONE (MILANO) ITALY
Phone+39.02.48600265 Fax+39.02.48600871
P.I. 09497700154 REA 126350
Copyright PROTEL
1988-2026 All Rights Reserved
Back to content